View UPC2710TB-E3-A_1331931.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

5V, SUPER MINIMOLD UPC2710TB MEDIUM POWER SI MMIC AMPLIFIER
FEATURES
* HIGH DENSITY SURFACE MOUNTING: 6 Pin Super Minimold or SOT-363 package * HIGH GAIN: 33 dB TYP * SATURATED OUTPUT POWER: +13.5 dBm * SUPPLY VOLTAGE: VCC = 4.5 to 5.5 V
35 VCC = 5.0 V
GAIN vs. FREQUENCY and TEMPERATURE
Gain, GS (dB)
TA = -40C TA = +25C 30 TA = +85C
DESCRIPTION
NEC's UPC2710TB is a Silicon RFIC manufactured using the NESAT III process. This device is suitable as a PA driver amplifier for cellular radio and other communication receivers. The UPC2710TB is pin compatible and has comparable performance to the larger UPC2710T, so it is suitable for use as a replacement to help reduce system size. The IC is housed in a 6 pin super minimold or SOT-363 package. NEC's stringent quality assurance and test procedures ensure the highest reliability and performance.
25 0.1 0.3 1.0 2.0
Frequency, f (GHz)
ELECTRICAL CHARACTERISTICS (TA = 25 C, VCC = 5 V, f = 0.5 GHz)
PART NUMBER PACKAGE OUTLINE SYMBOLS ICC GS fU GS PSAT P1dB NF RLIN RLOUT ISOL GT RTH PARAMETERS AND CONDITIONS Circuit Current (no signal) Small Signal Gain Upper Limit Operating Frequency (The gain at fU is 3 dB down from the gain at 0.1 GHz) Gain Flatness, f = 0.1 ~ 0.6 GHz f = 0.1 ~ 0.8 GHz Saturated Output Power Output Power at 1dB Compression Point Noise Figure Input Return Loss Output Return Loss Isolation Gain -Temperature Coefficient Thermal Resistance (Junction to Ambient) UNITS mA dB GHz dB dBm dBm dB dB dB dB dB/C C/W 3 9 34 +11 MIN 16 30 0.7 UPC2710TB S06 TYP 22 33 1.0 0.8 +13.5 +7.5 3.5 6 12 39 -0.006 325 5 MAX 29 36.5
California Eastern Laboratories
UPC2710TB ABSOLUTE MAXIMUM RATINGS1 (TA = 25C)
SYMBOLS VCC PIN PT TOP TSTG PARAMETERS Supply Voltage Input Power Power Dissipation2 Operating Temperature Storage Temperature UNITS V dBm mW C C RATINGS 6 +10 200 -40 to +85 -55 to +150
RECOMMENDED OPERATING CONDITIONS
SYMBOL VCC PARAMETER Supply Voltage UNITS V MIN 4.5 TYP MAX 5.0 5.5
Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on 50 x 50 x 1.6 mm epoxy glass PWB (TA = +85C).
PIN DESCRIPTIONS
Pin No. 1 Symbol Input Applied Pin Voltage (V) Voltage (V) - 0.9 Description Signal input pin. An internal matching circuit, configured with resistors, enables 50 connection over a wide bandwidth. A multi-feedback circuit is designed to cancel the deviations of hFE and resistance. This pin must be coupled to the signal source with a blocking capacitor. Signal output pin. Connect an inductor between this pin and VCC to supply current to the internal output transistors. Power supply pin. This pin should be externally equipped with a bypass capacitor to minimize ground impedance. - Ground pins. These pins should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be connected together with wide ground pattern to minimize impedance difference. Internal Equivalent Circuit
6 4
VCC OUT
4
Output
-
-
IN
1
6
VCC
4.5 to 5.5
3
GND
2
GND
5
2 3 5
GND
0
TYPICAL PERFORMANCE CURVES (TA = 25C)
CIRCUIT CURRENT vs. VOLTAGE
40 35 1.4 1.2 1.0 0.8 0.6 UPC2710T 10 5 0 0 1 2 3 4 5 6 0.4 0.2 0
40 35
CIRCUIT CURRENT vs. TEMPERATURE
Circuit Current, ICC (mA)
30 25 20 15
Circuit Current, ICC (mA)
30 UPC2710T 25 20 15 10 5 0 -60 -40 -20 0 20 40 60 80 100
Supply Voltage, VCC (V)
Operating Temperature, TOP (C)
UPC2710TB TYPICAL PERFORMANCE CURVES (TA = 25 C)
NOISE FIGURE AND INSERTION GAIN vs. FREQUENCY
35 VCC = 5.5 V Gp 6
RETURN LOSS vs. FREQUENCY
0 VCC = 5.0 V
Input Return Loss, RLIN (dB) Output Return Loss, RLOUT (dB)
Insertion Power Gain, GP (dB)
RLIN -10
VCC = 4.5 V 30 NF VCC = 5.5 V
5
Noise Figure, NF (dB)
VCC = 5.0 V
RLOUT -20
-30
4 VCC = 4.5 V VCC = 5.0 V
-40
25 0.1 0.3 1.0 2.0
3
-50 0.1
0.3
1.0
2.0
Frequency, f (GHz)
Frequency, f (GHz)
ISOLATION vs. FREQUENCY
0 VCC = 5.0V -10
20
POWER vs. FREQUENCY
15 PSAT
x
Isolation, ISOL (dB)
-20
Power (dBm)
10 P1dB 5
-30
-40
0
-50 0.1 0.3 1.0 2.0
-5 0 0.5 1.0 1.5 2.0
Frequency, f (GHz)
Frequency, f (GHz) X: Typical SSB Third Order Intercept Point OUTPUT POWER vs. INPUT POWER AND TEMPERATURE
20 VCC = 5.0 V f = 0.5 GHZ TA = 85 C
OUTPUT POWER vs. INPUT POWER AND VOLTAGE
20 VCC = 5.5 V f = 0.5 GHz 15
15
Output Power, POUT (dBm)
Output Power, POUT (dBm)
10 VCC = 5.0 V 5 VCC = 4.5 V 0
10 TA = -45 C 5 0 TA = 25 C
-5 -10 -15 -40 -35 -30 -25 -20 -15 -10 -5 0 5 10
-5
-10 -15 -40 -35 -30 -25 -20 -15 -10 -5 0 5 10
Input Power, PIN (dBm)
Input Power, PIN (dBm)
UPC2710TB TYPICAL PERFORMANCE CURVES (TA = 25C)
NOISE FIGURE vs. FREQUENCY
6
OUTPUT POWER vs. INPUT POWER AND VOLTAGE
+20 f = 1.0 GHz +15
5
Output Power, POUT (dBm)
VCC = 5.0 V VCC = 5.5 V
Noise Figure, NF (dB)
+10 +5 0 -5 -10
UPC2710T 4
VCC = 4.5 V
3
2 0 0.5 1.0 1.5
-15 -40 -35 -30 -25 -20 -15 -10 -5 0 +5 +10
Frequency, f (GHz)
Input Power, PIN (dBm)
OUTPUT POWER vs. INPUT POWER AND FREQUENCY
SATURATED OUTPUT POWER vs. FREQUENCY AND VOLTAGE
Saturated Output Power, POUT (sat) (dBm)
+20 VCC = 5.0 V +15
+20 PIN = -8 dBm +18 VCC = 5.5 V +16 VCC = 5.0 V +14 +12 +10 +8 +6 0.1 0.2 0.5 1.0 2.0 VCC = 4.5 V
Output Power, POUT (dBm)
f = 0.5 GHz +10 +5 f = 1.0 GHz 0 -5 -10 -15 -40 -35 -30 -25 -20 -15 -10 -5 0 +5 +10
Input Power, PIN (dBm)
Frequency, f (GHz)
Third Order Intermodulation Distortion, IM3 (dBc)
THIRD ORDER INTERMODULATION DISTORTION vs. OUTPUT POWER OF EACH TONE and VOLTAGE
-10
-20
VCC = 4.5 V
-30 VCC = 5.5 V -40 VCC = 5.0 V -50 f1 = 0.500 GHz f2 = 0.502 GHz -60 -10 -8 -6 -4 -2 0 +2 +4 +6 +8 +10
Output Power, POUT (dBm)
UPC2710TB SYSTEM APPLICATION EXAMPLE
Example of 900 MHz Band Digital Cellular Telephone
RX
DEMO
I Q
SW
PLL
PLL
I Driver
0
TX
PA
UPC2710TB
90
Q
UPC2710TB
TYPICAL SCATTERING PARAMETERS (TA = 25C)
3.0 GHz
0.1 GHz 3.0 GHz 2.0 GHz 1.0 GHz
2.0 GHz
0.1 GHz
1.0 GHz
S11
S22
UPC2710TB VCC = VOUT = 5 V, ICC = 22 mA
FREQUENCY GHz 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 MAG 0.306 0.324 0.356 0.400 0.439 0.469 0.481 0.488 0.479 0.465 0.448 0.417 0.387 0.350 0.316 0.292 0.256 0.245 0.215 0.201 0.177 0.161 0.145 0.124 0.113 0.107 0.091 0.081 0.067 0.055 0.039 S11 ANG 2.5 5.2 5.3 2.5 -3.3 -10.2 -17.9 -26.7 -34.5 -41.2 -49.3 -54.9 -61.2 -65.2 -70.8 -74.0 -76.9 -80.5 -82.9 -85.6 -84.4 -88.8 -88.7 -90.3 -89.8 -91.9 -92.2 -94.9 -97.4 -103.8 -95.6 MAG 43.072 43.517 44.432 45.513 45.679 45.670 44.793 43.016 40.519 37.946 35.122 32.108 29.221 26.656 23.895 21.576 19.567 17.743 16.040 14.717 13.475 12.327 11.154 10.262 9.490 8.793 8.149 7.652 7.134 6.726 6.295 S21 ANG -8.4 -17.1 -26.5 -36.9 -48.1 -59.7 -71.8 -84.3 -96.0 -107.3 -117.9 -128.0 -137.0 -145.8 -153.9 -161.6 -168.1 -174.4 179.6 173.5 168.8 163.1 158.7 154.4 150.4 146.4 142.4 138.9 135.1 131.5 128.4 MAG 0.012 0.010 0.010 0.012 0.012 0.013 0.014 0.014 0.013 0.016 0.016 0.015 0.015 0.015 0.013 0.016 0.015 0.018 0.017 0.021 0.020 0.021 0.022 0.023 0.025 0.028 0.030 0.031 0.031 0.039 0.039 S12 ANG 15.2 10.7 20.2 26.9 27.0 31.3 27.9 34.9 26.6 30.8 26.6 39.5 39.7 50.2 50.8 56.6 69.0 61.7 70.0 71.2 83.0 76.7 87.9 81.4 91.9 88.7 93.4 92.1 93.0 88.3 89.6 MAG 0.156 0.164 0.185 0.225 0.255 0.283 0.312 0.301 0.307 0.311 0.307 0.282 0.270 0.248 0.236 0.215 0.200 0.196 0.180 0.175 0.166 0.171 0.159 0.164 0.158 0.166 0.175 0.183 0.191 0.200 0.203 S22 ANG 2.7 2.1 0.3 -5.5 -15.4 -27.6 -54.9 -40.2 -92.2 -79.5 -92.2 -104.6 -115.5 -127.0 -136.2 -145.3 -155.2 -162.5 -173.4 -178.1 172.0 167.7 159.7 154.0 147.0 141.8 135.7 131.6 123.4 118.9 111.5 1.08 1.17 1.10 0.92 0.85 0.77 0.74 0.74 0.85 0.79 0.85 0.99 1.12 1.27 1.56 1.49 1.71 1.59 1.88 1.71 1.94 1.99 2.08 2.15 2.19 2.06 2.13 2.13 2.26 1.97 2.08 K
UPC2710TB OUTLINE DIMENSIONS (Units in mm)
PACKAGE OUTLINE S06 (Top View)
PIN CONNECTIONS
(Top View) (Bottom View)
2.1 0.1 1.25 0.1
3
4
4
3
C1F
2
5
5
2
0.65 2.0 0.2 1.3
3
4 0.22 - 0.05 (All Leads)
+0.10
1
6
6
1
2
5
1
6
1. 2. 3. 4. 5. 6.
INPUT GND GND OUTPUT GND VCC
0.6 0.1 0.45 0.13 0.05 0 ~ 0.1
TEST CIRCUIT
VCC 1000 pF
EQUIVALENT CIRCUIT
6
VCC
OUT
4
C3 L = 1000 nH 6 50 IN 1000 pF C1 1 4 1000 pF C2 50 OUT
1
IN
2, 3, 5
1. 2. 3. 4. 5. 6.
INPUT GND GND OUTPUT GND VCC
GND
2, 3, 5
ORDERING INFORMATION
PART NUMBER UPC2710TB-E3-A MARKING C1F QTY 3K/Reel
Note: Embossed Tape, 8 mm wide. Pins 1, 2 and 3 face perforated side of tape.
Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale.
EXCLUSIVE NORTH AMERICAN AGENT FOR
RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS
CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) * Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 07/17/2000
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of UPC2710TB-E3-A

	To Download UPC2710TB-E3-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .